How To Use Crimp Covers

Download Article

Crimp beads assist secure a loop on a piece of jewelry so that the finished slice can be attached to other components of jewelry. If you're making your own beaded jewelry, you'll probably need to crimp the wire on both ends to make sure the beads don't autumn off. For best results, yous should invest in a pair of crimping pliers, but a regular pair of pliers will work, besides. To apply crimp dewdrop, string on the crimp chaplet, course the bead, and complete the process past securing the decorative beads with one more crimp dewdrop.^[1]

i
Get together your supplies. Commencement, make up one's mind what size wire you have. Employ an online chart to make sure you lot have the right size crimp beads for your wire. Take into consideration how many strands of wire or thread you will be crimping at in one case, equally this will increase the size of dewdrop you'll demand.^[2]
- For example, if you are using i 0.020" (0.51 mm) piece of wire, you lot will need a bead with a diameter of 0.04" (ane.02 mm). But, if you are using 2 strands of wire, you will demand a dewdrop with a diameter of 0.08".
two
Add an end piece to your wire. To secure i cease of the wire so that your chaplet don't fall off, you lot'll need some sort of an end piece, such as a clasp. When you are ready to attach a squeeze, first thread the end of your beading wire (jewelry cable) through a crimp bead and then through the eye of the squeeze.^[3]
- Your design might telephone call for other kinds of finish pieces, such every bit a closed or solid bound ring or extender chain. The aforementioned methods utilize for these every bit for clasps.
Advertizement
three

Grade a loop. Form the loop through the squeeze and crimp bead. After threading the crimp and clasp, feed the wire dorsum through the crimp bead, forming a loop. Information technology is a proficient idea to get out a tail of wire a couple of inches longer than you think you need so yous will have some wire to piece of work with.^[four]

1

Slide the crimp dewdrop downwards the wire. Move the crimp bead close to the end of the clasp or end piece. Cheque the crimp bead and brand sure it is not also close to the clasp or end piece. Y'all desire to have a minor loop around the squeeze or end piece, but non and so small that it holds the squeeze so tightly that it cannot move freely. ^[five]
2

Flatten the dewdrop. Employ crimping pliers to flatten the dewdrop. Squeeze the beads with the flatter dorsum channel of the crimping pliers that is closest to the handle. Gently just firmly squeeze the pliers closed. This volition both flatten and identify a dent in the center of the crimp bead then that it resembles the letter "C".
iii
Round the dewdrop. Round it with crimping pliers. Place the dented crimp bead in the front, rounder channel of the crimping pliers, closest to the tip. Position the "C" upright so that when you lot close the pliers and clasp, the bead volition be folded closed right on the dent (endmost the "C" into an "O"). Squeeze gently but firmly and until the crimp bead has closed tightly around the wire.^[6]
- Tug gently to brand sure the wire doesn't pull gratis. If necessary, use pliers to get in shut tighter.
four
Use chain or needle nose pliers. If you don't accept a pair of crimping pliers, you tin utilize regular pliers. They get the job done, just they won't give you the same round, uniform crimps that crimping pliers will. To use these pliers, just grasp the crimp bead with the flat department of the pliers and clasp gently just tightly to smash the crimp bead flat onto the wire.
- But employ flat pliers or the flat section of pliers. The teeth in these pliers will also get out grooves on the surface of the crimp bead.

1

Cord your decorative beads. Utilize whatever beads you are designing your bracelet, necklace, or other piece of jewelry with. Thread your outset bead onto the wire. Thread the extra tail of wire through the bead hole. Use your affluent cutters to cut off the loose end of the string as close equally possible to the bead. Thread the residue of your beads according to your design until yous attain the other finish.^[7]
2
Tighten your chaplet. When yous are set to attach your concluding clasp to the end of your slice, thread the crimp dewdrop and squeeze simply like before, but now you lot will desire to tighten all of your chaplet past pulling on the tail end of the loose wire. This volition snug all your beads up together, leaving no gaps in your design.^[eight]
- You will demand to leave a pocket-sized, finger-nail length gap betwixt the beads if you have long tube chaplet in your blueprint.
- You need to brand sure the beads and wire make the small circumference effectually a wrist if you are making a bracelet.
- If y'all need more than leverage to pull the wire tight, use your pliers; ane to concord the clasp and the other to grasp and pull the wire.
3

Add a crimp cover for a squeamish affect. If you desire to hide your crimp chaplet, you can become crimp covers. A crimp cover looks similar a larger, round dewdrop that goes on top of the crimp bead or tube to give it a professional end. To add together a crimp comprehend, simply slide information technology over the crimp bead and squeeze it shut with a pair of pliers.^[ix]

References

Add New Question

Question

What can I use to secure the ends of my bracelets if thread slips through the crimp dewdrop?

That means that you need to apply a crimp dewdrop of a different size. This chart volition help you figure out the advisable size for your wire: http://www.firemountaingems.com/resource/encyclobeadia/charts/e94n
Question

What do I do if I've already threaded all the beads?

You volition have to take them off of the wire, start with a crimp bead, and so add together the beads on again.
Question

How can crimp beads exist used with earrings?

You tin make earrings using stringing wire, and y'all tin can crimp only similar yous would a bracelet or necklace.

Ask a Question

200 characters left

Include your email accost to get a bulletin when this question is answered.

Submit

Advertizing

Sometimes you don't go a perfect crimp. It either didn't fold over nicely or the wire pulls loose. If this happens, cut the crimp bead off the end, and just beginning over again with a fresh new crimp bead.

Thanks for submitting a tip for review!

Advertizing

Wear safety goggles when cutting beading wire. Steel beading wire can snap and fly effectually.

Things You'll Need

Two Crimp Beads
Option of Clasp
Length of Flexible Jewelry Wire (as well known as beading cable or stringing cable)
Beads
Crimping Tool or Concatenation Nose (Flat Nose) Pliers
Crimp Bead Covers (optional)

Nigh This Article

Article Summary Ten

To use crimp beads, thread a piece of jewelry wire through a crimp bead and a clasp, then feed the wire dorsum through the crimp dewdrop to class a loop. Motility the crimp bead close to the end of the squeeze. Side by side, use crimping pliers to flatten the bead in the middle to form a "c" shape and round out the shape. Thread the rest of your chaplet onto the wire according to your pattern until you achieve the other end. Then, tighten your beads and add a crimp comprehend as a terminal touch on to make your beading wait professional! For more tips on shaping crimp chaplet with pliers, read on!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 221,064 times.